Mon - Sat: 10:00 AM - 7:00 PM WhatsApp
Boom Barriers

eSSL Loop Detector – PSA02

Vehicle loop detector with presence and pulse relays for boom barrier lanes

  • Sensing range: 20~1500uH
  • Reaction time: 50ms
  • Power Voltage : 220VAC±10% 50/60Hz 24VAC/DC±10%
  • Sensing range : 20~1500uH
  • Sensitivity : 0.02%~0.2% (7degress selections)
  • Reaction time : 50ms.

Prices vary with quantity, software and installation needs. Contact us for the latest price.

eSSL Loop Detector – PSA02 Specifications

Power Voltage220VAC±10% 50/60Hz 24VAC/DC±10%
Sensing range20~1500uH
Sensitivity0.02%~0.2% (7degress selections)
Reaction time50ms
Frequency2 degrees selections, 15~120kHz
Output2 output relays (5A/AC230V), Relay1: presence relay, Relay2: pulse/fault relay
Operating mode Mode1presence& pulse relay output , Mode2: pulse/ fault relay
Presence modeLimited presence/ permanent presence
Pulse modePulse entry/ pulse exit
Pulse output timePulse entry: 200ms , Pulse exit: 200ms
Indicator Power indicatorred LED , Status indicator: green LED
Internal protectionIsolation transformer, voltage Regulator tube, voltage Dependent resistor.
Operating temp40℃~80℃.

Specifications are based on the manufacturer's published data and may change with model revisions. Please confirm before ordering.

What a loop does at your gate

A loop detector is what stops a barrier arm coming down on a car. A loop of wire cut into the road under the arm senses the metal of a vehicle sitting over it, and this unit reads that loop and tells the barrier a vehicle is there. It can also give the pulse that opens or closes the arm as a car arrives or leaves.

Reaction time is 50ms.

Relays, modes and settings

There are two relays rated 5A at 230V AC. Relay 1 is for presence, relay 2 for pulse or fault. Mode 1 uses presence and pulse outputs; Mode 2 uses pulse and fault.

  • Presence: limited or permanent
  • Pulse on entry or on exit, 200ms each
  • Sensitivity 0.02% to 0.2% across 7 steps
  • Two frequency settings, 15 to 120kHz
  • Loop inductance range 20 to 1500uH
  • Red power LED and green status LED
  • Power 220V AC, or 24V AC/DC

Two lanes side by side

The two frequency settings matter when an entry and an exit loop sit close together. Set them apart and the loops won't interfere with each other. The board is protected by an isolation transformer, a voltage regulator tube and a voltage dependent resistor.

eSSL Loop Detector – PSA02 FAQs

Can it run off a barrier's 24V supply?

Yes. It accepts 24V AC or DC as well as 220V AC.

What is the second relay for?

Relay 2 gives a pulse or a fault signal, depending on the mode. Relay 1 is the presence output.

Can I make it less sensitive?

Yes. Sensitivity runs from 0.02% to 0.2% over 7 steps.

Enquire About eSSL Loop Detector – PSA02

You may also like

Related Products

Boom Barriers

eSSL BB-Radar

79GHz radar vehicle sensor for boom barriers, detecting cars at 1-6 m

  • Working Frequency: 79GHz
  • Output Relay: NO/NC
  • Interface: Bluetooth/RS485
Boom Barriers

eSSL BG-108

8m aluminium boom barrier with a rest stand, for wide factory and warehouse gates

  • 8m boom
  • 8s open/close
  • IP54

Need an eSSL attendance or access control system?

Tell us your requirement and get the best price with installation and support.